![]() ![]() Neither his father nor his uncle Pavan (chairman and managing director of Inox Air Products) had prior experience in this sector. ![]() When he returned to India from the US in 2007, he shadowed his father Vivek (managing director, Gujarat Fluorochemicals Limited) for two years before deciding to enter the renewable energy sector. “We have a market cap of almost a billion-and-a-half dollars,” says Devansh, who, as director of his company, is the youngest family member to hold a position in the chemicals-to-multiplexes Inox Group. His company, Inox Wind, the renewable wind energy solutions provider, raised Rs 1,000 crore and was oversubscribed 18 times. In March 2015, the 28-year-old third-generation scion of Inox Group led one of the biggest initial public offerings (IPOs) that India has seen in the last two years. No one can accuse Devansh Jain of false pride. The Inox Group had no expertise in renewable energy, but backed by a successful IPO, third-generation scion Devansh Jain proved that there is profit in the sector 3 Small-Cap Stocks to Buy - Daily Stocks News on Inox Wind.Land Rover Media Hub – Nur ein weiteres Auto Bildideen on Manufacturing Facilities.Inox Login - Login Individual on Sitemap.INOX Wind: When promoters put in money in troubled business, it calls for deeper look.Inox Wind Board approves merger of Inox Wind Energy Limited into the Company.Inox Wind’s 3 MW Wind Turbine receives certification.Inox Wind’s 3MW Turbine gets Type Certification from Germany, paves way for commercial launch.Inox Wind receives Type Certification from TUV SUD for its 3 MW wind turbine.If any of the steps seem confusing, you can visit the original flutter sleeve dress sewing tutorial for a few more photos. If your daughter is on the short side, you might want to use 21 inches of elastic instead of 22. Use a safety pin to thread the elastic through. When you topstitch (in photo #2 above), do it from the underside so you can sew as close to the edge of the bias tape as possible. Make a casing for your elastic along the neckline: If you’ve never used bias tape before you may want to read this tutorial. These steps were a little hard to photograph, so I hope this makes sense. It looks like this:Īttach the sleeves to the dress (I’ve used photos from both the dress and top to try to best show the steps): It’s called single fold, but there are actually two folds in it. The under arms and neckline are finished with 1/2 inch single fold bias tape. You’ll want to cut 2 sleeve pieces, both on the fold, and two dress pieces, again both on the fold.Īdd the trim and finish the bottom edge of the sleeve: The pattern has 3/8 inch seam allowance built in. However, she’s fairly petite for her age, so if the girl you are sewing for is tall you will want to add some length (once it’s finished you can use a shoulder to knee measurement to decide exactly where to hem). Please note that I made this pattern to my daughter’s measurements and she is 3.5 years old and wears a 4T in clothes from the store. Don’t trim anything from the paper just butt the edges up against each other and tape. Print out the pattern and tape it together as you can see below. I’ve included a box on the third page that should measure exactly 1 inch when printed. You’ll want to be sure the printer settings say actual size or 100%. You can get the free flutter sleeve top and dress pattern in size 4T by clicking here. (I made this top from a shirt I thrifted for no particular reason other than that I loved the print.) The first version I made was cut a little low under the arm, so I fixed that in this version. I found it at Joann Fabrics for $2.99 for a roll of 2 yards. I used mini (3/8 inch) pom pom trim again to finish the sleeves and hem because it was so darn cute on the first version – and my daughter loves it. Those of you with girls other sizes could use the pattern as reference along with the instructions from the original flutter sleeve dress post to draft your own pattern – there’s only 2 pieces so it’s pretty simple.Īnd I thought this same pattern would probably look cute as a top, too, so I included a cut line on the pattern so you can use it to make either a dress or a shirt! Today’s post will give a few more details on how to sew either a dress or top from this pattern. I was excited that so many of you asked for a copy of the pattern! I’ve drawn up the pattern (in size 4T only) and you can download it for free later on in this post. Last week I shared a sewing tutorial for a girl’s flutter sleeve sundress and said I’d work on getting a pattern uploaded if people were interested. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |